Candy MODELS FOR UNDER-COUNTER FITTING Manual de usuario descargar pdf (Pagina 5)

Locating Your Drain, Water and Electrical Supply

IMPORTANT: OBSERVE ALL LOCAL CODES AND ORDINANCES

Review this page in detail. Look at the location where the dishwasher is to be located. Double check(ti I/)

that you have the correct water, electrical and drain supplies before attempting to make these connections.

NOTE: Figure 4 gives dimensional details that will be

helpful when making the decisions on how to run the

drain, water and electrical hook-ups.

Drain

Review Figures 6 & 7 to determine where you will con-

nect the dishwasher into your drain system. Cut the drain

hose hole

(11/z"

or larger) in area shaded in Figure 2.

Check BOTH sides of area to be cut BEFORE cutting,

to prevent interference. If the cabinet sidewall is wood,

sand the edges of the hole smooth. If the sidewall is

metal, install a protective grommet Part No. 302797,

available from your local Whirlpool dealer to cover the

edge of the hole.

It is recommended that the drain line be connected to

your house plumbing using a drain air-gap (Part No.

300096) available through your Whirlpool dealer.

NOTE: Some other brands of drain air-gaps restrict water

flow excessively and can result in incomplete drain.

If local plumbing codes permit, your dishwasher may be

connected directly to disposer or waste tee, provided that

connection is made ahead of trap and is at least 20”

above floor level. If additional drain line is required it must

be a minimum of

l/2)’

I.D. and should not be longer than

20 feet.

NOTE: To minimize vibration noise, the drain line must

be routed so that it does not touch adjacent cabinet

surfaces.

NOTE: When connecting to a separate drain trap, it

must be vented.

Water

Determine where you will connect the dishwasher into

your hot water supply. Review Figure 8 and note the loca-

tion of the water lines. The dishwasher water inlet valve

has 3/” IPS (Iron Pipe Size)

[l/2”

copper tubing] female

fitting. How much pipe or tubing will you need? Copper

tubing must have a minimum O.D. of 3/e”. Pipe, a

minimum of 3/e” IPS.

It is recommended that a shut-off valve be installed out-

side of the dishwasher area.

Cut the access hole (approximately

l/2”

or larger) inside

the shaded area as shown in Figure 2. Complete the

plumbing rough-in before putting the dishwasher in place.

The maximum water pressure allowed is 120 PSI

(Pounds Per Square Inch), dynamic. Minimum pressure

is 15 PSI.

The temperature of the water should be at least 14OOF.

Check this at your kitchen faucet. Let the water run before

checking the temperature with a candy or meat

thermometer.

Electrical Power Supply

Determine where you will connect to the electrical sup

ply. Review Figure 4 and 9, note the location of the elec-

tric lines. Cut the access hole inside shaded area as

shown in Figure 2.

A 120 Volt, 60 Hz, AC only, 15 Ampere (20 Ampere Max-

imum) fused electrical supply is required (Time delay fuse

or circuit breaker is recommended.) It is recommended

that a separate circuit serving only this appliance be pro-

vided. DO NOT use an extension cord.

Flexible Cord Connection

Local codes may permit the use of a UL listed flexible

three conductor cord terminated with a three prong

grounding type plug.

It is recommended that cord kit 675456, available at your

Whirlpool dealer or parts supplier, be used. If the cord

kit is not available locally, the flexible cord used must be

a three conductor 16 gauge cord that meets the National

Electrical Code and local codes and ordinances for this

type of installation. The length of the cord must not ex-

ceed six feet. It must be routed so that it does not touch

the dishwasher motor and/or the lower portion of the

dishwasher tub. If the flexible cord is used, it must be

plugged into a mating three prong grounding type wall

receptacle, grounded in accordance with the National

Electrical Code and local codes and ordinances.

Follow the instructions packaged with the flexible cord

and make sure the following requirements are met.

1. A UL approved strain relief must be installed at the

dishwasher junction box.

2. The power supply receptacle is installed as follows:

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comentarios a estos manuales

Sin comentarios

Candy MODELS FOR UNDER-COUNTER FITTING Manual de usuario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para No Candy MODELS FOR UNDER-COUNTER FITTING